PS1011-2410-0000 | Power supply PS1000; output: 24 V DC, 10 A; input: AC 100…240 V, 1-phase
PS1011-2410-0000 | Power supply PS1000; output: 24 V DC, 10 A; input: AC 100…240 V, 1-phase
Power supplies for 24 V and 48 V DC
The power supply PS1011-2410-0000 is a single-phase, 24 V DC power supply with an output current of 10 A and an output power of 240 W. On the input side, the device has a wide range input, a power factor correction (PFC) and an inrush current surge regulation. The output operates according to the UI characteristic curve and switches to safe hiccup mode in case of overload/short circuit. The power supply belongs to the PS1000 family and has a width of 49 mm. A DC OK LED and a potential-free relay contact monitor the status of the output voltage.
Product status:
regular delivery
Product information
| Technical data | PS1011-2410-0000 |
|---|---|
| Input voltage | AC 100…240 V |
| Wide-range input | yes |
| Input current | typ. 1.18 A at 230 V AC |
| Switch-on current limiter | yes |
| Mains frequency | 50…60 Hz |
| Starting current | typ. 16 A peak at 230 V AC |
| Harmonic correction (PFC) | active |
| Output voltage | 24 V DC |
| Adjustment range | 24…28 V DC |
| Output current | 10 A |
| Output | 240 W |
| DC OK LED | yes |
| Efficiency | approx. 95.2% |
| Operating temperature | -25…+70°C |
| Shock resistance | conforms to EN 60068-2-27 |
| Vibration resistance | conforms to EN 60068-2-6 |
| Weight | approx. 540 g |
| Approvals/markings | CE, UL61010 |
| Protection rating | IP20 |
| Housing data | Power supply |
|---|---|
| Dimensions (W x H x D) | 49 mm x 124 mm x 124 mm |
| Material | polycarbonate |
| Installation | on 35 mm DIN rail, conforming to EN 60715 with lock |
| Wiring | input/output: screw type connection,
signal contact: push-in technique |
| Connection cross-section | input/output: e*: max. 6 mm², f*: max. 4 mm², a*: max. 4 mm² signal contact: e*: max. 1.5 mm², f*: max. 1.5 mm², a*: max. 1.5 mm² |
| Max. cable diameter with end sleeve | Input/Output: 2.8 mm, Signal contact: 1.6 mm |
| Connection cross-section AWG | Input/Output: AWG20-10 Signal contact: AWG28-16 |
| Stripping length | 7 mm |
*s: solid wire; st: stranded wire; f: with ferrule
| Material compliance | PS1011-2410-0000 |
|---|---|
| CAS No. | 1317-36-8 |
| REACH SVHC | Lead(II) oxide |
| REACH Annex XVII | compliant |
| REACH Annex XIV | compliant |
| SCIP No. | SCIP submission in progress |
| POP | compliant |
| RoHS | compliant with exemption |
| RoHS exemption | 7a: Lead in solders with a high melting point with a minimum mass fraction of 85% lead |
| CA Prop65 | www.beckhoff.com/prop65 |
| Disclaimer | This statement and the information contained above are, to the best of our knowledge and belief, accurate, based on the information we have received from our suppliers. This information is in line with the current standard of technology and our suppliers’ technical documentation. The absence of the substances is not verified by Beckhoff Automation by means of analytical tests. When addressed to our customers any information contained in this document is subject to the terms and conditions expressed in the governing customer agreement. Our general terms and conditions apply. |
Loading content ...
Loading content ...
© Beckhoff Automation 2026 - Terms of Use